profitbion.blogg.se - Sparkbox generator

#SPARKBOX GENERATOR HOW TO#
#SPARKBOX GENERATOR MANUAL#

Note: To avoid potential damage to your new ignition box, we recommend that you perform the ground loop test described on our web site technical support page before plugging in a new ignition box.Ĥ. If the tests indicate a fault exists, repair any fault that may exist in the vehicle, and then plug in the module. Before plugging in the connector, perform the distributor signal test and the ignition module ground test. Bolt the ignition box to the relay panel. Plasmatronics part number SC010 ignition coil is recommended for use with all Perma-Tune ignition systems.ģ. Note: To avoid potential damage to your new ignition box, we recommend that you replace the ignition coil when the ignition box is replaced. Replace the coil if the coil does not test to specifications or if there is evidence of oil or tar leaking from the coil. Perform an ignition coil resistance test. Failure to reconnect this ground strap may result in damage to the car or your new ignition box.Ģ. It is extremely important that this ground strap be reconnected when the relay panel is bolted back to the car. This ground strap can be easy to forget to hook back up because when it is removed from the relay panel it will fall forward between the fuel filter and fuel accumulator where it cannot be seen. One of the screws for the relay panel mounting also holds the braided ground strap that provides the ground for the relay panel. NOTE: On some cars, the relay panel where the ignition box is located must be unbolted from the car so that the nuts can be held while the bolts for the ignition box are unscrewed. Perform any maintenance procedure needed, if the bench check procedure indicates so, to prevent damaging the new ignition module upon its installation. Perform a bench check of the module according to the manufacturers specifications.

#SPARKBOX GENERATOR MANUAL#

Remove the old ignition module from the car according to the shop manual for this car.

O Flying lead connector for easy installation and maintenance.ġ. O External, repairable, fusible link to protect the vehicle and Perma-Tune from ground loop damage. O Black anodized housing that resists corrosion and is paint able.

O Larger housing to accommodate more robust, reliable components. The Model 911SC902 supersedes the Model 911SC Perma-Tune and has many improvements over the older model: New features of the Model 911SC902 Perma-Tune This part is designed to be installed by a mechanic that is familiar with European automobiles and safety standards.

#SPARKBOX GENERATOR HOW TO#

Installation Instructions on how to install a new Porsche 911 6 pin Spark Box or CDI unit.ĭISCONNECT THE BATTERY BEFORE INSTALLING OR SERVICING ANY IGNITION SYSTEMS COMPONENTS.įailure to follow these instructions and the vehicle owners handbook and shop manual could result in serious personal injury, death and or damage to property.

The Preserving Bin is treated as a thatch structure and can be damaged by anything except non-explosive ranged attacks.By design911 on Thursday, November 11, 2010.

The description says, “Cooks Jerky Over Hours” when it’s really only 36 minutes, but this certainly refers to in-game time.

Additionally, adding crude oil would likely pose serious health issues for humans if ingested.

Jerky in real life must be made with raw meat in order to retain enough moisture to still be palatable, as opposed to cooked meat like in the game.

For more information on spoilage and timings, see Spoilage. Placing a single Sparkpowder in the bin will keep it running for 30 minutes. The Preserving Bin is powered by Sparkpowder. Factoring stack and inventory limits, the most convenient ratio is 1:1 for single-type production (stacks of meat to stacks of sparkpowder) or 2:2:3 for multi-type (cooked meat to cooked prime meat to sparkpowder). This does not take into account spoilage, so the exact yield will be off. For example, 20 meat would need 84 sparkpowder while 20 prime and 20 regular would require 144 sparkpowder. The formula to find how much Sparkpowder would be needed to produce X jerky, including both the recipe requirement and to keep the appliance powered for the duration, is X × 4.2 for a single type, or ×3.6 for both types concurrently, rounded up. The Preserving Bin can produce both Cooked Meat Jerky and Prime Meat Jerky simultaneously. Unlike the Large Storage Box, the Preserving Bin fits inside a one-wall-tall hut. Creating Jerky requires both Oil and Sparkpowder, in addition to the Sparkpowder required to power the appliance. Jerky lasts for 20 days in the Preserving Bin. Producing Jerky in the Preserving Bin takes 36 minutes. In addition to preserving food, the Preserving Bin can make Cooked Meat Jerky or Prime Meat Jerky.